Step 2

Then pull detergent spout through cut out area.

Step 3

Place the enclosed measuring cup under the dispensing faucet. To dispense detergent, turn knob on faucet counter clockwise.

Step 4

Turn knob clockwise until “click” is felt to stop dispensing.

Step 5

Applies to 5L and 3L laundry detergent: For High Efficiency washers, use 15ml (1 Tbsp) of detergent per laundry load. For regular washers, use 30ml (2 Tbsp) of detergent per load. Follow manufacturer’s washing instructions for water temperature.

Step 2

Apply 2 sprays directly onto stains and surrounding area. For maximum results, spray the stain both outside and underneath on the inside of the garment.

Step 3

Allow the stain remover to work and soak into the stain for 5 minutes or more.

Step 4

Place into the regular wash with detergent; for best results use our Excelsior® HE Laundry Detergent.

Step 2

Pour a small amount (2ml) of Excelsior® HE Machine Cleaner & Deodorizer onto a clean cloth or sponge.

Step 3

Use this to wipe the rubber seal around the door of the HE washing machine, removing all visible residue.

Step 4

Follow with a fresh clean damp cloth or sponge to then remove all Excelsior® HE Washing Machine Cleaner & Deodorizer from the rubber seal. Wait one minute for the rubber seal to dry.

Step 5

Place the used cloth or sponge into a hamper to be cleaned with your next wash.

Once a month (or whenever odors or residues are noticed):

Step 6

Place 50ml (approximately 3 tablespoons) of product into the empty HE washing machine detergent drawer or directly into the drum.

Step 7

Close the door/lid of the washing machine and set the machine to “normal cycle - hot water”. Make sure the washer is empty. Allow the entire cycle to run and fully rinse.

Step 1

Follow the steps below to connect the water to your new washer:

Ensure your water source is turned off before beginning.

Step 2

Insert a flat washer into each end of the hoses. Check that washers are firmly seated in couplings.

Step 3

Using the hoses provided from the 304XS Stainless Steel Hose Kit, attach the 90' elbow end of the cold water (blue) hose to the cold-water inlet valve on the back of the machine; then the hot water (red) hose to the hot water inlet valve.

Step 4

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 5

Attach the opposite end of the hot water (red) hose to the hot water faucet.

Step 6

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 7

Attach the opposite end of the cold water (blue) hose to one of the two splits in the Y-connector.

If your washer is part of a set, which is not stacked, then consider the following: If the washer is on the left, connect the hose to the left split. If the washer is on the right, connect the hose to the right split.

Step 8

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 9

Insert a flat washer into each end of the Steam Kit hoses. Check that washers are firmly seated in couplings.

Step 10

Using the 6-foot hose provided in the Excelsior® Steam Kit, attach the 90 elbow end to the inlet valve on the back of the dryer machine.

Step 11

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 12

Attach the opposite end of the 6-foot Steam Kit hose to the second split in the Y-connector.

If your washer is part of a set, which is not stacked, then consider the following: If the washer is on the left, connect the hose to the left split. If the washer is on the right, connect the hose to the right split.

Step 13

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 14

Using the 12-inch inlet adapter hose provided in the Excelsior® Steam Kit, attach one end to the remaining opening in the Y-connector.

Step 15

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 16

Attach the opposite end of the 12-inch inlet adapter hose to the cold-water faucet./p>

Step 17

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 1

Follow the steps below to connect the water to your new washer:

Ensure your water source is turned off before beginning.

Step 2

Insert a flat washer into each end of the hoses. Check that washers are firmly seated in couplings.

Step 3

Attach the 90˚ elbow end of the cold water (blue) hose to the cold water inlet valve on the back of the machine; then the hot water (red) hose to the hot water inlet valve.

Step 4

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.

Step 5

Attach opposite end of cold water (blue) hose to the cold water faucet. Attach hot water (red) hose to the hot water faucet.

Step 6

Hand tighten couplings, then use pliers to make an additional 1/4” turn clockwise. Do not over-tighten couplings, as damage can result.